mcd-demo2---PIC 16F87X Microcontroller Development Board ( Brand new )

Click to see large image

Ideal for the Student or Hobbyist to start developing and testing your PIC projects with this multi-featured and flexiable PIC Development board.

• PIC 16F87X  Development board 2 consists of : 
• 8 indicator LEDS
• ICD2 Header connector for programming / Debugging with Microchips ICD2
• 16x2 LCD Character display
• 6 Seven segment display
• RS232 Serial communication port
• 16 button matrix Keypad
• Stepp motor slot
• 4 push buttons
• Infrared reception
• DB9 connector and RS232 Transeiver (for serial Comms)
• I2C Serial EEprom 24c01B - dipswitch used for write enable and setting device address (on supported eeproms)
• 2 pin sockect for main Osc (4MHz resonator -Default) allows for easy changing of the main Osc frequency.  Provion for loading caps if using a crystal.
• Buzzer
• Reset switch
• Uncommited PIC I/O ports - So the PIC's I/O lines may be connected to any of the onboard modules or external circuits

4*4 Matrix keyboard – to test password lock and other items.s.	Buzzer voice/PWM output experiment – to practice normal voice, music and PWM output sound.	5-way independent key-press–for easy various key-press input experiments.	RS-232 communication for connection with a PC or any other device with a DB9 connector
Infrared remote-control receiver – to practice infrared remote-control decoding and all kinds of infrared remote control.l.	All I / O output to facilitate expansion	IIC (I2C) communication – to read/write 24CXX series chips with hardware IIC or software IIC directly.	SPI communication–to read/write EEPROM of 93CXX with hardware SPI or software analog SPI,to select 8-bit or 16-bit read/write method through jumper.
Clock selection – jumper for switch between various oscillation modes, to replace crystal vibration of different frequency as required by development of product.	DS18B20 digital temperature sensor – 1-wire bus communication, wide range for temperature measurement, high accuracy and sensitivity (remark: chip DS18B20 is optional).	Stepper motor driver circuit(remark: Setpper motor is optional).	Simulation debugging interface – to directly connect ICD1/ICD2/MCD1/MCD2 and carry out on-line simulation for on-board chips and resources
On-board power module – can connect to the polarity of external AC or DC power supply optionally, voltage range 7-12V	mcu/mpu reset key	1-way A/D converter signal input.	8-way independent LED
12864-character LCD–128*64 lattices.(remark:12864- character LCD is optional). 1602-character LCD–internal 5*7 lattices, to display 16*2-character. 6-bit 7-segment digital tube – to realize dynamic or static display experiment of digital tube, to display clock,temperature or to make counter. 　 　 128*64LCD is optional Setpper motor is optional

1. mcd-demo2--PIC 16F87X Microcontroller Development Boar  
2. serial cable
3. 1 x RJ12 Connection Cable.
4. 16F877A Chip
5. 1602 LCD with Yellow backlight   
6. CD-ROM (Development PCB Layout,Development Board Schematic,Sample code (C / ASM) for each onboard module, MPLAB 7.50 .)
7. Power supply(110-240 AC TO 9V DC)

• DS18B20 ( DS1820 ) Temperature Sensor(TO-92 package)  - US$3.00 for each
• 12864-character LCD Module Yellow Backlight    - US$14.00 for each
• 1602(16x2) Characters LCD Module  HD44780  Each additional US$3.00
• Stepper Motor - US$4.00 for each
• Dupont wire expansion connection 10pcs rad +10pcs black(30cm long)  - US$2.00 for each
• PIC16F873A(DIP28)- US$4.00 for each
• PIC16F876A(DIP28) - US$4.20 for each
• PIC16F877A(DIP40)- US$4.50 for each
• PIC18F452(DIP40)- US$6.00 for each